Abstract: This application note is a reference design for a PC-based temperature measurement system. It uses the MAX1396 and MAX6603EVKITs, a MAXQ2000 microcontroller, and MAX6603 signal conditioner. The design presents an easy way to obtain the temperature readings from the MAX6603 without requiring complicated conversion formulas. Schematics, block diagrams, and software are all provided. Introduction This reference design describes how to create a PC-based temperature-measurement system for evaluating the MAX6603 signal conditioner. The design uses two EV (evaluation) kits, the MAX1396EVKIT and a MAX6603EVKIT, and an easy to use software program. The MAX6603 converts ambient temperature to a voltage signal by using two platinum thermistors. The MAX1396EVKIT provides the analog-to-digital conversion to measure the output voltage signal from the MAX6603EVKIT. Then the MAX1393EVKIT sends that signal to the PC. The software converts the received data to temperature values which are displayed on the screen. Setup Overview MAX6603 The MAX6603 is a dual-channel, platinum, RTD-to-voltage signal conditioner. It excites and amplifies the signal from two series-connected on-board 100Ω platinum resistive temperature devices (Pt RTD) to achieve high-voltage, level-filtered signals for temperature measurements. This reference design uses the MAX6603EVKIT to measure the temperature. The Pt-RTDs mounted on the EV kit board can be electrically disconnected from the circuit by removing the shunt on JU4 and allowing an external Pt-RTD to be connected to the MAX6603 through twisted-pair cabling. MAX1396 The MAX1396 is a 312.5ksps, 2-channel single-ended, 12-bit SAR ADC. It is used in this design to measure the output voltage from the MAX6603EVKIT. Please follow the instructions in the MAX1396EVKIT data sheet to install the EV kit. Hardware Apply a +6V to +9V voltage supply to the HVIN pad of the MAX6603EVKIT, and connect the negative terminal of the voltage supply to the GND pad. The OUT1 and GND pads of the MAX6603EVKIT need to be connected to the AIN1 and the GND pads of the MAX1396EVKIT. Use a USB cable to connect the MAX1396EVKIT to the PC. Figure 1 shows the hardware system setup. More detailed image (PDF, 416kB) Figure 1. Hardware system block diagram. The MAX6603EVKIT consists of the MAX6603, all required passive components, and a proven PCB layout. The MAX6603EVKIT schematic is shown in Figure 2 and Table 1 shows the jumper settings. Figure 2. MAX6603EVKIT schematic. Table 1. MAX6603EVKIT Jumper Settings Jumper Position JU1 1-2 JU2 1-2 JU3 1-2 JU4 1-2 The MAX1396EVKIT consists of one MAX1396 device, one MAXQ2000 microcontroller, all required passive components, and a proven PCB layout. The MAX1396EVKIT schematic is shown in Figure 3 and Table 2 shows the jumper settings. More detailed image (PDF, 452kB) Figure 3. MAX1396EVKIT schematic. Table 2. MAX1396EVKIT Jumper Settings Jumper Position JU1 1-2 JU2 1-2 JU3 1-2 JU4 1-2 JU5 1-2 JU6 1-2 JU7 1-2 Windows® Program Overview This program (Figure 4) has an easy-to-use graphical user interface that is compatible with Windows 98SE/2000/XP. It displays the output voltage of the MAX6603EVKIT and the corresponding temperature readings from the platinum thermistors on the screen. Once the MAX1396EVKIT is connected to the PC through the USB cable, the MAXQ2000 waits for the commands from the Windows program. Start the program and a window similar to Figure 4 should appear. If a message box says, "No Virtual COM Port Detected," close the program, reconnect the USB cable, and restart the program. After the software starts up, by default the Auto Read box is checked. The software continuously sends the Read Temp command to the MAX1396EVKIT to measure the OUT1 voltage of the MAX6603EVKIT. The temperature is read at a rate set by the Time Interval pulldown menu. After the software receives the measured OUT1 voltage value, the corresponding temperature value will be displayed in the upper left corner of the screen. To have more accurate ADC readings, use a digital voltmeter to measure the reference voltage on pin 1 of JU7 on the MAX1396EVKIT. Enter the value into the MAX1396EVKIT reference voltage edit box. If this is done correctly, the ADC readings should have less than 0.1% error. Measure the actual supply voltage on pin 1 of the JU1 on the MAX6603EVKIT, and enter the value into the MAX6603 supply voltage edit box. This step is important because the formula, which is used to convert the output voltage of the MAX6603 to temperature, depends on the value of the supply voltage. Figure 4. The reference design's software measures the temperature from the EV kit and voltage from the MAX6603. Windows is a registered trademark of Microsoft Corp. 相关型号   APP 4531: Sep 25, 2009 MAX1396 1.5V至3.6V、312.5ksps、单通道真差分/双通道单端、12位SAR ADC 完整的数据资料 (PDF, 704kB) 免费样品 MAX6603 双通道、铂电阻、RTD至电压信号调理器 完整的数据资料 (PDF, 480kB) 自动更新 需要自动接收最新发布的应用笔记吗？请订阅EE-Mail™ (English only)。 我们期待您的反馈！ 喜欢？不喜欢？有待改善？或为我们提供建议？请与我们联系 — 我们将根据您的意见或建议改善我们的工作。 网页评价或提供建议   下载，PDF格式 (71kB)  AN4531, AN 4531, APP4531, Appnote4531, Appnote 4531